Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit
- Compatible with chassis with “open” PCI slot design. Modding might be required.
- Included 220mm riser Cable
- Vertically Display a VGA Graphics card
- Easy Installation, placing tray over all seven PCI slot spaces
Reddazon may receive an affiliate commission if you make purchases on Amazon.com through this site. Thank you for using these links to support Reddazon.
Reddit Posts and Comments
0 posts • 121 mentions • top 50 shown below
3 points • Joko_on_Smoko
Holy shit. Think I could put a vertical GPU mount in this thing? I've always wanted a mini itx case with a vertical GPU. Maybe this one?
2 points • Drakeziel
The best I have seen is the Phanteks GPU mount , because it pulls the gpu further from the window panel for better airflow and much cleaner look. Some users have said they have to remove parts of the rear case brackets to fit.
2 points • ScubaSteve7886
Almost all cases that have vertical mounts will restrict airflow.
Something like this would be a great option if you want to mount your GPU vertically.
2 points • wHiTeSoL
I'm using this one here, it's super sturdy.
2 points • Marzoval
It's the Phanteks riser. I may get the Lian-Li 3-slot riser if the 3090 requires it.
2 points • iamkurumi
There's also the Phanteks Vertical GPU Mount, but that's dependent on if the PCI-E area is completely open once you remove the PCI-E brackets. If not, you'll have to mod the case.
2 points • Computerknight54
Get a pair of side cutters to make room for the GPU's IO and you can use a mount like this https://www.amazon.com/Phanteks-PH-VGPUKT_02-Universal-Vertical-Pci/dp/B07MW73HTJ
2 points • SpaceCatCadet
2 points • Lanky-Association952
Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_api_glc_fabc_.WzZFb2F30DGE
2 points • Ekipl331
Phanteks PH-VGPUKT_02 – Universal... https://www.amazon.com/dp/B07MW73HTJ?ref=ppx_pop_mob_ap_share
2 points • Painter2002
So it does not come with a vertical GPU mount by default. Lian Li does make a vertical mount, but it has mixed reviews and is pricey.
If you have an o11 Dynamic (regular or XL) case, I’d highly suggest this one made by Phanteks: Phanteks Vertical GPU Mount. It comes with a X16 riser cable and was a very install and had no sag, at least with my card. I also notice no difference in GPU performance while gaming, same frame rates as before when it was horizontally installed.
2 points • Truthful27
The case vertical mount is not good for temps! The universal one is way better. I like to keep everything the same so that’s why I went with 120s all around!
Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_api_fabc_u3EUFbX7GQEWQ?_encoding=UTF8&psc=1
2 points • Spymonkey13
Just take a look the pics. It's all self explanatory. Bare in mind that this is for two slot cards. If your card is any fatter it won't fit.
2 points • MagicWithEarvin
2 points • Joeys2323
You can buy vertical mounts for your gpu, it has an extension pcie cable with it
1 points • Ritter18
The GPU is a GIGABYTE AORUS GeForce RTX 2080
And here's the bracket -
Phanteks PH-VGPUKT_02 – Universal... https://www.amazon.com/dp/B07MW73HTJ?ref=ppx_pop_mob_ap_share
1 points • jiivn
Personally prefer the phanteks vertical mount
Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_api_glc_fabc_DoG5Fb0HQ1EFD
1 points • Opp47
And just about 7/8 of an inch
1 points • Steiny2175
Phanteks PH-VGPUKT_02 - Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_apa_i_aUcmEbW0B597Q
1 points • Junstar
Yup! I used the Phanteks Vertical GPU mount. It sits flush on top of the Corsair LL120 fans so it may have looked that way lol
1 points • King_Avalon
I hate to be that guy, but if you're really wanting to make it work I'd install a PCI riser in there.
Such as this one, https://www.amazon.com/Phanteks-PH-VGPUKT_02-Universal-Vertical-Pci/dp/B07MW73HTJ/ref=asc_df_B07MW73HTJ/?tag=hyprod-20&linkCode=df0&hvadid=320048880417&hvpos=&hvnetw=g&hvrand=395459082183106358&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9015071&hvtargid=pla-659524775226&psc=1&tag=&ref=&adgrpid=61389685902&hvpone=&hvptwo=&hvadid=320048880417&hvpos=&hvnetw=g&hvrand=395459082183106358&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9015071&hvtargid=pla-659524775226.
1 points • RagingPanda1
I have one from Phanteks. I chose it because it barely adds any length to the gpu and as you can see, its super tight in my case! I painted the bracket and thumbscrews white. Here's the link: https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_sms_apa_i_dvBREbTXMHTB3
1 points • -xMrMx-
Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_api_i_9kGjFbCFVD2WX This is a good solution
1 points • ellisthedev
GPU stands vertical if the case allows it. Then you use a PCI-e ribbon cable to connect it to the mobo. Because it’s vertical, you won’t notice the ribbon.
A bracket like this, or just the ribbon cable part will do.
Phanteks PH-VGPUKT_02 - Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_api_i_DckvEbV1KZ74Q
1 points • WARMONGERE
1 points • StevoMcVevo
Unless its a plastic front version I would mount the fans on the outside and radiator inside and you should be able to pull it off with it mounted to the bottom fan if you can remover the HDD cage. Admittedly it would likely be tight but I would try that first. Just my two cents. A universal vertical mount would make it easier. Just options
1 points • SkvaderArts
Something like the ones I linked in the post. Like this one.
1 points • Trotter-x
You would have to remove that bottom fan but you could mount your card vertically. I am using a Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket to vertically mount my 5800XT. The bracket comes with the PCIe extension cable. The only thing is that you have to set the PCIe slot to x3 instead of x4 because the cable is not x4 (they don't make them yet). I discovered this through trial and error and the advice of a few friends
3 points • zZz_clay
There's a few manufacturers that make kits, but this one seems to be the most widely used universal one. Hope this helps. https://www.amazon.com/Phanteks-PH-VGPUKT_02-Universal-Vertical-Pci/dp/B07MW73HTJ/ref=sr_1_1?crid=2VXGMXJOGDNFG&dchild=1&keywords=phanteks+vertical+gpu+mount&qid=1597712213&sprefix=phanteks+ver%2Caps%2C220&sr=8-1
1 points • projectspectrum
Phanteks is perfect. I’m doing a build now - 80mm of clearance (on top of the mounting rack) on bottom.
In stock at amazon. $40. I’m showing May 11 arrival date, but that’s COVID-19 delays not stock.
Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_tai_MxkNEbA5K578E
I’ve heard CableMod is great too, but it’s not in stock.
1 points • nhuynh50
1 points • LifeGoalsThighHigh
If you make or adapt something similar to this and use a riser cable, yes, it would. You'd just block your other slot.
1 points • Lesbian_Hipster
Would it happen to be this one: https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_apa_i_mHzXEb3M9PQ14
I ran into the same problem with op, thought it was the XL too.
1 points • moobzforlife
Using this one https://www.amazon.com/Phanteks-PH-VGPUKT_02-Universal-Vertical-Pci/dp/B07MW73HTJ/ref=redir_mobile_desktop?ie=UTF8&psc=1&ref=ppx_pop_mob_b_asin_title
1 points • Archieezzy
Phanteks PH-VGPUKT_02 - Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_api_i_dbUwEb0VVKQ4S
1 points • 4ourthdimension
1 points • Jakobabs
I was thinking of getting something like this, and mounting it to the bottom, hopefully with a radiator under it. I might need some standoffs so that I could fit a displayport cable. Phanteks said that the case will be back in stock in November, so hopefully by then ill also have a 2080 and the waterblock. I'm really hoping things fit, but if not I guess I'll put it on the back
1 points • AdenoidLlama080
Yes u can as that case has 1 dedicated part for vertical so u would just need to get something like this will allow u to put a second vertical one in.
1 points • deathtochina6969
This is the one i bought https://www.amazon.com/Phanteks-PH-VGPUKT_02-Universal-Vertical-Pci/dp/B07MW73HTJ/ref=sr_1_1?dchild=1&keywords=vertical+gpu+mount&qid=1585859880&sr=8-1
1 points • krylo76302
I bought this one. Works perfect https://www.amazon.com/dp/B07MW73HTJ?ref=ppx_pop_mob_ap_share
1 points • Hypnotoasted
Used the phanteks mount, reasonably priced and the gpu cable that comes with it is great. Havent seen any fps issues with it mounted like this.
1 points • mk1817
Something like this? Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_api_i_PYexFbH18RYWC
1 points • SinglSrvngFrnd
Phanteks mount. With some motherboards you will need to switch from auto to pcie3 in the bios but it has no effect on performance.
1 points • canela209
Looks like the phanteks bracket ,I recently got it as well for the same case ,https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_sms_apa_i_uM06EbGPQ2QW8
1 points • EgoExchange
Absolutely, purchased mine from Amazon so dug up a link.
Phanteks PH-VGPUKT_02 - Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_apa_i_YhEqEbX47Q991
Bonus, the included cable is of better quality.
Mine from TT came frayed out of box and was causing issues.
1 points • nazzo123
Phanteks PH-VGPUKT_02 – Universal Vertical GPU Bracket with 220mm Flat Line Pci-E X16 Riser Cable Kit https://www.amazon.com/dp/B07MW73HTJ/ref=cm_sw_r_cp_api_fab_d32FFbTW2RJAR
If there’s a less slot support let me know but this is what is fitting so far with a 90 degree fitting.
1 points • armislt
> evga watercooling bracket for the xc ultra
Would Phanteks PH-VGPUKT_02 universal mount work as well?
1 points • BillClintonEatsPasta
1 points • dusktildawn48
Yeah it looks great
That's the one I bought. Worked super easy.
1 points • DamagedGoods13
u/Glosed1 sorry for my slow response. Its this Phanteks riser. Right now there's about an inch below the bracket, but I can still move the card up another inch or so... so if I move the card all the way up, there should be enough room for a 360 Slim radiator with a fan, i would think. If not, it would be real close.